mediapi/README.md

hardware: raspberry pi 4 4GB ram os: raspberry pi os lite (64 bits) use-cas: almost always offline. except when doing maintenance

Git remotes

Two remotes are configured; GitHub is just a mirror of the Forgejo repo.

• origin (primary) — ssh://forgejo@forgejo.jmopines.com:2222/jm/mediapi.git
• github (mirror) — git@github.com:jmtremblay2/mediapi.git

origin is set up with two push URLs (forgejo + github), so a single git push mirrors to both. Fetch still comes from forgejo only.

git push origin master   # pushes to forgejo AND github

To re-create the dual-push setup on a fresh clone:

git remote set-url --add --push origin ssh://forgejo@forgejo.jmopines.com:2222/jm/mediapi.git
git remote set-url --add --push origin git@github.com:jmtremblay2/mediapi.git

AP on the raspberry pi

• must have access point that boots up on system boot
• ssid + password come from .env (MEDIAPI_AP_SSID / MEDIAPI_AP_PASSWORD)
• fine if it's slow, fine if it does not boot right away (wait for other services)
• (I will connect to the AP from my phone and control what the pi plays)

Setup (Raspberry Pi OS Bookworm / NetworkManager)

install.sh creates/updates the AP connection for you from the .env values (see Configuration below), so normally you don't run these by hand. For reference, this is what it does — substitute the MEDIAPI_* values from your .env:

# set the wifi regulatory domain (required, affects allowed channels/power)
sudo raspi-config nonint do_wifi_country "$MEDIAPI_WIFI_COUNTRY"

# create the AP connection profile on wlan0
# ipv4.method=shared makes NetworkManager run its own DHCP server (dnsmasq)
# on wlan0 for the phone to get an address from -- no internet sharing/NAT
# involved since there's no other upstream connection active
sudo nmcli connection add type wifi ifname wlan0 con-name "$MEDIAPI_AP_CONN_NAME" \
  autoconnect yes connection.autoconnect-priority 100 save yes \
  802-11-wireless.mode ap 802-11-wireless.band bg 802-11-wireless.ssid "$MEDIAPI_AP_SSID" \
  wifi-sec.key-mgmt wpa-psk wifi-sec.psk "$MEDIAPI_AP_PASSWORD" \
  ipv4.method shared

# bring it up now (it will also auto-start on every boot from here on)
sudo nmcli connection up "$MEDIAPI_AP_CONN_NAME"

# verify
nmcli connection show "$MEDIAPI_AP_CONN_NAME"
ip addr show wlan0

To remove it later: sudo nmcli connection delete "$MEDIAPI_AP_CONN_NAME"

app to browse media

media will be stored at

• /localmedia
• more TBD

I want an app that runs on the raspbery pi with two modes:

• playback
• control the app should have two buttons up top that show the two modes all the time. the manager will switch back and forth between the two. the rest of the screen will be used to show the content. Must fit on one phone screen

control mode

• shows the media stores
• the user can click on any one of them to "go" inside the folder
• at any point in time the user can chose to "play" a folder, or a file (how TBD)
• radio buttons up top of that panel (below and separately from the two global modes)
  • keep playing
  • more TBD
• has basic navigation (pretty buch go back one level at the time)

playback mode:

• display the file being played
• displays playback info (current time, total video time), volume control
• pause/play, back and fast forward 30 seconds (or whatever you can get on the framework you use)
• plays on both HDMI mirrored if connected.

basic auth

• login username + password come from .env (MEDIAPI_USERNAME / MEDIAPI_PASSWORD)
• fine to keep known devices logged in forever pretty much

easy to run ... I don't want to have to download a gazillion things

Configuration (.env)

All per-deployment config (login, media paths, port, the AP ssid/password, the Linux user the services run as) lives in a single .env file at the repo root. It is gitignored — never commit it. Copy the template and fill it in:

cp .env.example .env
# then edit .env

.env is read two ways, so it stays the single source of truth:

• the Flask app parses it at startup (mediapi/config.py, no extra dependency),
• install.sh sources it to configure the AP + render the systemd units.

Keep values simple (no spaces / shell-special characters).

Setup (mediapi app)

Implemented as a small Flask app (mediapi/) + a permanently-running mpv player controlled over its JSON IPC socket. mpv renders video to HDMI directly (DRM/KMS, no desktop needed); the phone browser only shows metadata/controls, never the video image itself.

Dual-HDMI mirroring. A single mpv on DRM can only drive one connector, and the Pi's vc4-kms driver can't clone two HDMI outputs onto one framebuffer — so mirroring is done by running one mpv per connected screen. scripts/start-mpv.py (launched by the mediapi-mpv unit) enumerates the connected HDMI connectors and starts a primary mpv (audio + the app's IPC socket, mpv.sock) plus a mirror mpv per extra screen (video-only, on mpv-mirror-<connector>.sock). The app plays/pauses/seeks the primary and echoes those to the mirrors best-effort, re-syncing on every video. One screen → same as before; a dead mirror just leaves that screen dark, never the audio screen. Because each screen runs its own mpv, the same file decodes once per screen (--hwdec=auto-safe falls back to software if the HW decoder is busy).

First-time install (on the Pi)

# system deps: mpv for HDMI/DRM playback
sudo apt update
sudo apt install -y mpv

# install uv (Python package/venv manager) if not already present
curl -LsSf https://astral.sh/uv/install.sh | sh   # installs to ~/.local/bin/uv

# create your .env (see Configuration above)
cp .env.example .env && $EDITOR .env

# deploy the currently-checked-out ref: syncs deps, adds the service user to
# the video+render groups (GPU/DRM access for HDMI), configures the AP,
# installs+starts the services. Run as your normal user -- NOT with sudo, or
# the services get rendered to run as root.
./install.sh

# verify
systemctl status mediapi-mpv mediapi-app
ls -l /run/mediapi/mpv.sock

Then, from a phone connected to the AP (MEDIAPI_AP_SSID), browse to http://<pi-ap-ip>:8080/ (the AP's gateway address, typically 10.42.0.1 — confirm with ip addr show wlan0 on the pi) and log in with the MEDIAPI_USERNAME / MEDIAPI_PASSWORD from your .env.

Deploying updates

install.sh deploys whatever git ref is currently checked out — it does not pull on its own, so you control exactly which version goes live (pin a tag for a reproducible car deployment). It syncs deps, re-applies the AP config, reinstalls the systemd units (rendered from the .template files using your .env), restarts the services, and health-checks the app. The same script is used for the first install and every update; each run is idempotent and cleans up the previous deployment in place.

After a healthy deploy it records the deployed commit in instance/deployed_ref. If a new deploy fails its health check, it rolls back to that last-known-good ref automatically and re-checks.

git fetch --tags
git checkout v1.2.0     # pin the version you want
./install.sh

# or let the script do the checkout for you:
./install.sh v1.2.0

Passing a ref checks it out with git checkout --detach before deploying; with no argument it deploys the current checkout as-is (branch or tag).

It refuses to run while the read-only overlay is active (changes would vanish on reboot) and prints the disable/re-enable steps. So the update loop is:

sudo raspi-config nonint do_overlayfs 1 && sudo reboot   # disable overlay
# ... after reboot:
cd ~/mediapi && ./install.sh v1.2.0
sudo raspi-config nonint do_overlayfs 0 && sudo reboot   # re-enable overlay

Notes / things to double check on the actual hardware (couldn't be verified from a dev machine):

• dtoverlay=vc4-kms-v3d should already be set in /boot/firmware/config.txt on current Bookworm Pi4 images (needed for DRM output) — worth a quick check.
• Mirroring picks up whatever HDMI connectors read connected under /sys/class/drm/card*-HDMI-*/status at service start — so plug in both screens before mediapi-mpv starts (or sudo systemctl restart mediapi-mpv after). Check what it launched with sudo journalctl -u mediapi-mpv | grep start-mpv and confirm both sockets: ls -l /run/mediapi/mpv*.sock. mpv --drm-connector=help (with a display attached) lists the connector names if the sysfs guess is ever wrong.
• If audio doesn't come out of the TV, check aplay -l for the HDMI ALSA device name (usually vc4-hdmi) and add e.g. --audio-device=alsa/plughw:CARD=vc4hdmi0,DEV=0 to the mpv unit template, or run sudo raspi-config nonint do_audio 2 to force HDMI as the default output.

To stop/remove: sudo systemctl disable --now mediapi-mpv mediapi-app